10 steps to follow when your swimming pool PVC pipes leak. It’s only natural that one’s first instinct is to panic when a swimming pools PVC pipes begin to leak.
Despite this, there are measures which you can take to handle this situation efficiently. Below, you can find a comprehensive guide composed of 10 steps to follow when your swimming pool PVC pipes leak which you can adopt to make the best out of this situation.
Contents
- 1 10 Steps to Follow When Your Swimming Pool PVC Pipes Leak
- 1.1 Step One: Determine if There’s A Legitimate Leak
- 1.2 Step Two: Determine Where the Leak is Located
- 1.3 Step Three: Determine Which Pieces to Replace
- 1.4 Step Four: Remove the Defective Plumbing
- 1.5 Step Five: Drain Excess Water
- 1.6 Step Six: Assemble the Replacement Pieces
- 1.7 Step Seven: Apply Primer
- 1.8 Step Eight: Glue
- 1.9 Step Nine: Wait
- 1.10 Step Ten: Call a Professional
- 2 Final Verdict
10 Steps to Follow When Your Swimming Pool PVC Pipes Leak
Step One: Determine if There’s A Legitimate Leak
If you suspect that your pool has a leak, then there are tools which you can use to know with certainty.
There is one of the best ways of 10 steps to follow when your swimming pool PVC pipes leak to do so is to mark your pool’s current water level with chalk. As time passes, the water levels will lower significantly below the chalk.
After you’ve determined that there is a leak, you can proceed to the next step.
Step Two: Determine Where the Leak is Located
You can’t treat the problem if you don’t know where the source of the leak is, to begin with.
By determining where the leak is, you can start to assess the overall damage to your pipes, and you can determine what your next steps should be.
Ideally, you should find the source of the leak as soon as possible so that it doesn’t worsen.
Step Three: Determine Which Pieces to Replace
A PVC pipe is often installed with glue fittings; therefore, it is unrealistic to replace the entire pipe.
This is 3 step of 10 steps to follow when your swimming pool PVC pipes leak.
If the leak occurs within two inches of one of the pipe’s joints, then it is better for yourself and the PVC pipe if you change specific pieces and fittings.
Step Four: Remove the Defective Plumbing
First, you are necessary to turn off the water that is accessed by your swimming pool. Once you’ve done this, you can cut about, or more than, an inch of piping on both sides of the leak with PVC cutters.
You can cut the piping by placing the cutters at a ninety-degree angle where the desired cut is to be done.
Next, you force down with the cutters until they’ve forced through the pipe.
Step Five: Drain Excess Water
You don’t want to have water running inside the pipes while you’re working because it can compromise the process and it’s simply a hassle.
Instead, allow the excess water to drain completely out of the pipes of 10 steps to follow when your swimming pool PVC pipes leak and wipe down either end of the pipes with a cloth.
Step Six: Assemble the Replacement Pieces
You should now assemble the pieces that you’ll use to replace the old, defective ones.
Dry-fit them into their desired positions and make adjustments where you see fit before you glue them. After you’ve assembled and sized everything, you can disassemble them so that you can prime and apply glue.
Step Seven: Apply Primer
Primer is an absolute necessity when you’re fixing a PVC pipe. Primer should be used inside the fittings and outside of pipes.
To do so, you must use an applicator brush which will aid you in applying a coat of primer to the designated surfaces. This is 7 steps of 10 steps to follow when your swimming pool PVC pipes leak.
Step Eight: Glue
After you’ve used the primer, you can begin gluing your replacement pieces. First, glue the inside of your replacement fitting(s) and the outside of your pipe.
Twist your replacement fitting into the pipe because the helps the replacement fit slide into the pipe.
Be sure to hold the two pieces together so that they remain glued.
Step Nine: Wait
Keep gluing your pieces together until all of the replacement fittings are in place. You should also follow of 10 steps to follow when your swimming pool PVC pipes leak.
You must let the glue work for about fifteen minutes before you resume water pressure because if the glue isn’t completely set, then it can destroy the entire process.
Once the glue is dried, you can reapply water pressure.
Step Ten: Call a Professional
If you don’t want to step through the above steps or if something goes wrong then don’t be afraid to call a local professional. This will cost you more money; however, you’ll have the confidence of knowing that your PVS pipe has been fully restored.
Final Verdict
Already you have seen 10 steps to follow when your swimming pool PVC pipes leak .
When your PVC swimming pool pipe begins to leak, you don’t always have to call a professional. You can, instead, gather the proper materials and follow the above guide to fix the leak on your own.